Відео

They look great. Where do you get Baltic birch plywood? Nobody around here even knows what it is. I like the look of it and probably wouldn’t use edge banding. I’ll save that for regular plywood, which seems to be the only thing I can get in my area.

Great work really..do you have dimensions and measurements?

Are you using side mount slides as bottom mount? No problem?

You made that look so easy!!! Hopefully ours will go that same way. Thanks so much!!

This video is exactly what I am looking for. Thank you. What slide did you use for the bottom slide? Did you also use the side-mounted side for the bottom?

Your setup was uneven. You should measure how far apart you want the rails to sit then adjust both sides so you are centre on the cart, this will evenly distribute the weight on both wheels. That’s why it has measurements on the sliding rail. Also, the stand should be facing the bow. 😊

yeh $800 electric conversion kit... OUCH

Thank you

I love the design

Different strokes for different folks, but I would have skipped the edge banding. One of the best things about Baltic birch is that the edges look so nice.

Dang! What a great solution for getting around that center support! Thanks..... that earned a sub!

I got this one but don’t leave your kayak hooked up to the cart while in storage or in your garage. The info says it’s rated at around 300 lbs. I left my cart hooked up yo my kayak while in my garage and the tires are hard plastic and will leave a dent in the tires.

Did you use Side Mount slides for your bottom mount slides? I am considering doing the same as i have a lot of slides left over and would rather use them than buy more. Thanks! Great video.

Hi. How long did you make the vertical peice for the transducer

@5:23: Where you live, do they allow exposed NM cable in the cabinet (e.g., to your garbage disposal)?

Hi, is there anyone who know how to do the same thing on a SeaDoo Spark (2019) ?

Great idea.

No fasteners?

Is there a second thermostat for this motor?

What are the cabinet floor slides they look different from the drawer slides?

Hi mate why didn't you just heat the pvc and squashing it flat it's a lot better stronger as well 😊😊😊

I have 22 gti se 170 and I have to have the key connected to reset.. PSA for anyone with that model

You're out of frame during the assembly process.???

Great video, especially the trick about the 4th plug that was hard to get to. We had already spent an hour trying to replace it. That was the only spark plug we had to replace after it had worked it's way loose. Now the engine starts nicely, and runsn well overall, but the idle is much higher, leading to very rough forward or backward changes. Can you think of something we might have hit that screwed up our idle? Thanks.

I own the same exact ski and I cant clear this code to save my life (I should add that I performed the required maintenance).

Great project! And I know it's a weird compliment, but that is the nicest plywood I have ever seen 🤣

Just wondering, does the 90 degree elbow just friction fit? I would have guessed that moving the transducer up and down into the water would wear it out and become loose. I know the line won’t allow you to lose the transducer, just thought it may be annoying if the elbow pops off, or gets so loose the transducer might ride up.

Can I start from the bottom up ??

So does the transducer arm not move when ur moving in the water ?

how about on 2022 rxpx.Thank you

Hi i have an ober heating problem on my 60 hp merc 6 4 stroke on my 2014 mako skiff It keeps overheating at full throttle.. i dont think it should be doing this.. ive done every maintenance possible and new thermostat water impellar the boat runs excellent has perfect conpression.. it just doesnt seem to like running at full throttle even for 2 minutes over heats and has a problem.. but it never throws an over heat alarm? Does your boat not run full throttle? Seems to like 4500 rpms and under

Did you add the drawer slides to the underside of the sliding boxes and then slide them into the slides mounted on the 3/4 plywood strips. Would this allow you to then push the strips to the back wall to screw in and then slide the cabinet forward to screw through the slide into the bottom of the cabinet. I watched the video a few times but could not figure out the order the slides were aligned and then mounted. Thanks in advance

What brand of ladder

how about for a 2018 155 wake ?

Good video. I'm putting an hour meter on my 50hp. Wonering if I have to take the coil pack off to get closer to the actual plug or if it's close enough to wrap it by the coil pack. Thought you may know. Thanks

Have you tried it in sand on a beach. Every one I've used digs down into the sand..

Did a similar setup on my first kayak. I bought a scotty mount and found that the 1/2” pvc will slide through the side of the scotty mount. This enabled the arm to swing up easily. Only issue was it would swing up a little too easy at times when moving fast the water would swing it up some. Used that for years and eventually bought the scotty arm that goes into the top of the mount. The scotty arm was like $20-$30

I'd very much like to see the video...mine is on its way so any help is most appreciated

oh man .. i need this. Can you share the exact model ladder you used here? thanks.

Clever!!

Grtting my goodoes to rog this up myself! Grest idea, thanks for sharing sir! 💪🏼😎

I have the same boat and want to install this for scalloping season. I’d love to see the installation video if you have it. If not…please provide the materials used in the installation. Thanks!

Hey lookin to do this but somehow worried about the gunwale taking all that repeated force there … 🤔

Hi how long have you had that VEVOR Heavy Duty Kayak Cart, and has it broke on you at all? Also do you have to strap it down?

The funniest thing is I hate mdf but I found out most ‘high end’ cabinets use mdf because you can get a piano gloss finish with it And the high end people that want the high gloss don’t care if it’s mdf

how about i build a platofrm with wheels hook it to this and ride

I got one for my Bonafide RS117. It’s been great so far!

i changed my spark plugs on my 40hp fourstroke. when i started it the idle was very uneven and running rough when giving gas. engine stopped with non-critical engine failiure. Any clues for a rookie boat mechanic? thanks from Sweden for a good educational video

U made that look really easy your goated bro #newsubscriber 🔥

Do you know if this will convert a ClicGear pushcart with a fixed front wheel?